Flat Tan Wood Grain Patina Leather Watch Strap
$69.00
Lug & Buckle Width
Lug width is the gap between the two lugs of your watch case, where the strap fits. Your strap has to match it exactly.
Most watches are 18, 20 or 22 mm. Measure inner edge to inner edge with a ruler — or flip your old strap over: the width is often printed inside.
Our sizes read lug / buckle: 20 / 18 mm is 20 mm at the watch, 18 mm at the buckle. Only the first number has to match your watch.
Widths we cut
- 12
- 14
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- mm
Another width? Choose Custom and enter your own.
Buckle width
The width of the strap where the buckle sits — the second number in our sizes. 20 / 18 mm means 18 mm at the buckle.
Every strap comes with a matching buckle. Keeping your own? Measure across the inside of its frame and choose Custom.
Not sure? Email support@xilugs.com with your watch’s brand and model — we’ll confirm before we cut.
Strap Length Guide
Every strap has two parts: the long end with the holes and the short end with the buckle. 115 / 70 mm means 115 mm long, 70 mm short.
Wrap a soft tape — or a paper strip — just above the wrist bone. Snug, not tight. Then find your size below.
Find your size
Suggested fit. Watch over 44 mm: go one size shorter. Like it loose: one size longer.
| Long / Short | Your wrist |
|---|---|
| 105 / 65 mm | up to 14.5 cm |
| 105 / 70 mm | 14.6 – 15.5 cm |
| 115 / 70 mm | 15.6 – 16.5 cm |
| 115 / 75 mm | 16.6 – 17.5 cm |
| 125 / 75 mm | 17.6 – 18.5 cm |
| 125 / 85 mm | 18.6 – 19.5 cm |
| 135 / 85 mm | 19.6 – 20.5 cm |
| 135 / 95 mm | 20.6 – 21.5 cm |
| 135 / 105 mm | 21.6 – 22.5 cm |
| Custom size — type your own lengths | |
Between two sizes? Take the larger one — or choose Custom and enter your own lengths.
Not sure? Email support@xilugs.com with your wrist size — we’ll confirm before we cut.
Straight or curved end?
This is the end of the strap that meets your watch case.
Straight end — cut straight across. Fits almost any watch; a small gap at the case is normal.
Curved end — cut in an arc to follow the round edge of the case, so the strap sits flush with no gap. Tell us your watch brand and model and we’ll match the curve.
Not sure? Choose Straight — it fits everything.
Not sure? Email support@xilugs.com with your watch’s brand and model — we’ll confirm before we cut.
Keepers
The two small leather loops on the buckle half — the strap tail slides through them so it lies flat.
- Match leather — both loops in the strap's own leather.
- One colour — one colour for both loops.
- Two colours +$5 — the Top loop and the Bottom loop each in their own colour.
Tap the guide to zoom in — drag to move around.
-
FlatEven thickness, no padding.
2.5–4.5 mm
-
Padded DomedBuilt up in the middle and rounded down to thin edges.
3.5–5.5 mm
-
Padded SquareA raised centre with a flat top and crisp squared shoulders.
3.5–5.5 mm
-
Padded FullPadded edge to edge, the thickest profile.
3.5–5.5 mm
On padded straps the number is the height at the centre; the edges are thinner.
- Thin dress watch (case under 10 mm)2.5–3.5 mm
- Everyday watch (10–13 mm)3.5–4.5 mm
- Sports / diver / large case (over 13 mm)4.5–5.5 mm
A good rule: the thicker the watch case, the thicker the strap can be.
Check the gap between your lugs and the case. Some watches have a tight gap, and a thick padded strap may not fit. If unsure, send us a photo of your watch in the Note / Watch Photo fields and we'll confirm before cutting.
Need a size not listed? Choose Custom and enter it.
Not sure? Email support@xilugs.com with your watch model — we'll recommend one before we cut.
Standard pins, hidden inside the strap. Swap with a spring-bar tool.
Small lever on the back. Swap by hand in seconds, no tools.
Warm honey tan; deepens with wear.
Light neutral sand; stays clean and quiet.
The leather
Hand-Dyed Patina
Wood Grain Patina is a hand-dyed calfskin where the dye is drawn out into long, parallel figures that read like cut timber. It takes the same layered dyeing as our other patinas with one extra step: the grain is worked in by hand while the dye is still open. The effect is strongest in raking light, and no two straps carry the same figure.
Built for daily wear
Watch Strap Structure
Every strap is built around the three details that decide how it lives on your wrist — not the ones that photograph well.
-
01
Quick release spring bars
Choose quick release or regular spring bars. We fit them before it ships, so you can change straps in seconds — no tools, no scratched lugs.
-
02
Soft Zermatt lining
The underside is lined with soft, water-resistant Zermatt — comfortable against the skin all day, and in warm weather.
-
03
Your name on the lining
Initials or a name, hand-stamped into the lining free of charge, so the piece on your wrist is one of one.
PACKAGING
Every strap arrives in a wooden box
No envelopes, no plastic mailers. Every XILUGS order ships in our own wooden box, lined with a shock-absorbing foam insert that holds up to four straps securely in place. A spring bar tool is tucked inside, so you can fit your new strap the day it arrives, and the box keeps your collection safe long after.
- Wooden box with every order
- Holds up to 4 straps
- Shockproof foam insert
- Spring bar tool included
You may also like
-
Blue Patina Leather Watch Strap
Regular price $69.00 USDRegular price -
Cognac Red Patina Leather Watch Strap
Regular price $69.00 USDRegular price -
Coffee Black Patina Leather Watch Strap
Regular price $69.00 USDRegular price -
Purple Black Patina Leather Watch Strap
Regular price $69.00 USDRegular price
New design — no reviews yet. Here’s what customers say about our shop:
